GUIDE LIBRARY · FREE2 guides

Airbrush Reviews: 0.2–0.5 mm Nozzle and PSI Guide

Set the nozzle and pressure first, then choose gravity or siphon, single or dual action. Three jobs show where the numbers hold, without paid brand ranking.

2actionable guides
2popular entries
0paywalls
EXAMPLES

Three jobs: set the nozzle and pressure before the brand

These are starting points, not guarantees. Pressure shifts with paint viscosity, nozzle size, distance and humidity; test on scrap with the paint you actually use. Ranges reference Scale Model Shop's nozzle guide and BT Airbrush's PSI table (accessed 2026-11-03).

1/72 aircraft, miniatures and soft-edge camouflage0.15–0.2 mm · 8–12 psi

A small nozzle and low pressure are for fine lines and soft edges. Thin acrylic toward milk consistency and check the fan on scrap. Above about 12 psi the paint can blow out and dry rough at the edge; below about 8 psi the flow stutters and the tip clogs. Drop about 5 psi at 2–3 cm, add about 5 psi beyond 20 cm.

Everyday base coats on Gundam and car models0.3 mm · 12–18 psi

0.3 mm is the all-rounder most people should start with: base coats, camouflage and light shading all fit. Build thin layers instead of one wet coat. At the same price, check whether nozzles and needles are sold separately before counting the extras in a kit.

Primer, clear coat and metallic over larger areas0.4–0.5 mm · 20–25 psi

Primer and clear coat are heavier and flow better through a larger nozzle; metallic paint may need 25–30 psi to spread the flakes. Seal with a light pass first, then build the second layer without parking the airbrush in one spot.

Long runs on large parts and colour changesSiphon · 0.5 mm · 20–25 psi

A siphon bottle carries more paint for long sessions, but it takes more solvent to flush and is less steady at low pressure. Gravity feed is easier for small areas and low-pressure detail; siphon solves capacity, not status.

FAQ

Six questions to settle before you buy

Is a 0.2 mm nozzle always better than 0.3 mm?

No. 0.2 mm is for miniatures, camouflage and fine lines, but it is less forgiving with thinning and cleaning. 0.3 mm handles most base coats and camouflage with more margin. For a first airbrush, 0.3 mm is usually the safer buy.

Do I need dual action?

Not necessarily. Dual action separates air and paint for gradients and detail; single action locks a flow rate and suits repeated coverage. Match the trigger to the work, not to a spec sheet.

How thin should acrylic paint be?

Start at milk consistency and add thinner or flow improver in small steps. Brands differ a lot, so test on scrap. Too thick clogs and spatters; too thin runs and loses coverage.

Is higher PSI better?

No. Above about 25 psi you can blow paint out of recesses and under masking tape; below about 10 psi the flow stutters and the tip clogs. Miniatures usually start around 12–18 psi; primer and metallics go higher.

Gravity or siphon feed?

For small areas, low pressure and frequent colour changes, gravity feed is easier. For large parts and long continuous sessions, siphon feed carries more paint. Cleaning and minimum working pressure differ, so do not choose on cup position alone.

Do I have to disassemble after every colour?

Flush the cup, channel and nozzle between colours to avoid muddy mixes; do a deeper needle and nozzle clean at the end of the session. Keep water-based and solvent-based cleaning routines separate, and check that replacement nozzles and needles are available before buying.

01 · POPULAR

Popular topics

Start with the 2 most-read topics, or search everything.

02 · START HERE

Start here

Don't get lost: start with the picks, then expand by topic.

All 2 guides →
03 · ALL GUIDES

All content

Filter by keyword; each guide has steps, common mistakes and a checklist.

04 · HOW

How to use this site

STEP 01

Pick a real problem

Start from a recommendation or search, not the first page; find the problem you need to solve now.

STEP 02

Follow the steps

Each guide gives steps, common mistakes and a checklist; do the smallest step first, then iterate.

STEP 03

Review with the checklist

Check your work with the checklist; drop what does not fit and keep the repeatable process.

05 · WHY

Why read this

01

Not vague concepts

Every guide lands on steps, templates, mistakes and a checklist you can actually use.

02

No invented results

No promises of income, traffic or admission; professional topics state limits and point to experts.

03

Kept updated

Last updated 2026.11.03; content grows from feedback instead of one-off empty pages.

Affiliate disclosure: this page may contain affiliate links. We may earn a commission if you buy through them, at no extra cost to you.

Top picks

Three priority picks screened by need, budget and use.

Iwata

Dual-action/precision

Price: High

Check price
Grex

Dual/detail

Price: High

Check price
Harder & Steenbeck

Premium/precision

Price: Very high

Check price

See all picks